ZohgoCheck an address free

Zoning in Bay Ridge, Brooklyn

What is Bay Ridge zoned?

Bay Ridge's most common district is R5B: 2,581 of its 10,144 tax lots (25.4%) are in R5B, based on PLUTO 26v2 lots inside the 2020 NTA boundary. R5B allows a standard residential FAR of 1.50 and a maximum height of 35 ft for standard buildings (ZR 23-21, ZR 23-422). Check any Bay Ridge address free on Zohgo.

Bay Ridge is a low-rise R4 and R5B neighborhood almost entirely inside the Special Bay Ridge District.

Tax lots
10,144PLUTO 26v2
Most common
R5B25.4% of lots
Commercial overlay
1,182lots (11.7%)
Median lot
2,200 sq ftlot area

Bay Ridge is a low-rise neighborhood by zoning. Of its 10,144 tax lots, 8,623 (85.0%) are in R2 through R5B districts, led by R5B (2,581 lots) and R4-1 (2,241). Only a thin layer of R6B (882), R6A (214), R7B and R7A allows apartment buildings above 35 feet.

Almost the whole neighborhood, 9,711 lots (95.7%), is also inside the Special Bay Ridge District (ZR Article XI, Chapter 4). Its stated purpose is to preserve the existing scale and character of the community (ZR 114-00), and it modifies the underlying rules in a few concrete ways listed below.

Zoning districts in Bay Ridge by tax lot

Zoning district (zonedist1)Tax lotsShareStandard residential FARMax height (standard residences)
R5B2,58125.4%1.50max 35 ft
R4-12,24122.1%1.0025 ft perimeter wall, 35 ft ridge (pitched-roof envelope)
R4A9119.0%1.0025 ft perimeter wall, 35 ft ridge (pitched-roof envelope)
R3-28848.7%0.75max 35 ft (25 ft perimeter wall / 35 ft ridge for 1-2 family detached, semi-detached or zero lot line homes)
R6B8828.7%2.00base 30-45 ft, max 55 ft
R4B7036.9%1.00max 25 ft
R3-16556.5%0.7525 ft perimeter wall, 35 ft ridge (pitched-roof envelope)
R25915.8%0.7525 ft perimeter wall, 35 ft ridge (pitched-roof envelope)
R6A2142.1%3.00base 40-65 ft, max 75 ft
C4-2A (commercial)1331.3%3.00 (as R6A, its residential equivalent)
R7B1281.3%3.00base 40-65 ft, max 75 ft
C8-2 (commercial)600.6%no residences (C8)
All other districts (8)1611.6%
Total10,144100%

Source: PLUTO 26v2, field zonedist1 (the district covering the largest part of each lot), lots inside the 2020 NTA boundary BK1001. FAR and heights are the ZR 23-21 / 23-22 and ZR 23-421 / 23-422 / 23-432 limits for standard residences; qualifying affordable or senior housing can go higher. Commercial districts use their residential equivalent from ZR 34-112.

What the main districts allow

What can you build on your Bay Ridge lot?

Zohgo shows the zoning district, FAR, height and setbacks for any NYC address in about a minute. Free to start, sign in with Google or Apple.

Check any NYC address free on Zohgo

Commercial overlays

1,182 lots (11.7%) carry a commercial overlay: C1-3 on 887 lots, C2-3 on 273 lots, C1-4 on 12 lots, C2-4 on 11 lots. An overlay sits on top of a residence district and allows local retail and services, usually on the ground floor of avenue and corridor buildings, while the residential rules of the underlying district still apply. For a zoning lot with only commercial use, the overlay FAR is 1.00 where the overlay is mapped in R1, R2, R3-1, R3A or R3X, 1.60 in R3-2, and 2.00 in R4 and every higher residence district (ZR 33-121).

Special districts

Three Special Bay Ridge District rules worth knowing before a first pass:

Historic districts

54 lots (0.5%) sit in a designated historic district according to PLUTO, led by Bay Ridge Parkway-Doctors' Row Historic District (54). Zoning still sets the envelope, but exterior work on these lots also goes through the Landmarks Preservation Commission, so a lot that zones for more floor area may not be able to use it.

380 lots (3.7%) are split by a district boundary (PLUTO splitzone). On those, each portion follows its own district; see split zoning lots.

Worked example

Take a 2,200 sq ft lot in R5B, close to the neighborhood's median lot size. At the standard FAR of 1.50, the maximum residential floor area is 2,200 x 1.50 = 3,300 sq ft (ZR 23-21). With qualifying residential site rules the FAR is 2.00, so 2,200 x 2.00 = 4,400 sq ft. For a standard multiple dwelling outside special density areas, the unit cap divides floor area by the dwelling unit factor of 680: 3,300 / 680 = 4.85, which allows 5 units because fractions of 0.75 or more count as a unit (ZR 23-52).

How we counted

We took every tax lot in PLUTO 26v2 (NYC Department of City Planning, August 2026), kept lots whose latitude and longitude fall inside the 2020 Neighborhood Tabulation Area polygon for Bay Ridge (BK1001), and counted the zoning district PLUTO lists first (zonedist1). Lot counts are not land area: one large lot counts the same as a 20-foot rowhouse lot. Zoning maps change through rezonings, so always confirm the district for a specific address.

Bay Ridge zoning FAQ

What is the most common zoning district in Bay Ridge?

R5B. In PLUTO 26v2, 2,581 of the 10,144 tax lots inside the 2020 Bay Ridge NTA boundary (25.4%) have R5B as their main district.

What FAR does R5B allow?

R5B allows a standard residential FAR of 1.50 and 2.00 for qualifying residential sites (ZR 23-21).

How tall can a building be in R5B?

For standard residences: max 35 ft (ZR 23-422).

How many apartments fit on a 2,200 sq ft R5B lot?

At FAR 1.50 the lot allows 3,300 sq ft of residential floor area. Divided by the dwelling unit factor of 680 that is 4.85, so 5 units for a standard building outside special density areas, since fractions of 0.75 or more count as a unit (ZR 23-52).

Can I build a backyard ADU in Bay Ridge?

Not everywhere. Within the Special Bay Ridge District, backyard ancillary dwelling units are not permitted in the portion west of Ridge Boulevard or south of Marine Avenue (ZR 114-02). Elsewhere in the district the citywide ADU rules apply.

Related pages

Sources

Lot counts are our own tabulation of PLUTO 26v2 inside the 2020 NTA boundary, pulled October 27, 2026. PLUTO is updated a few times a year, so counts will drift.