Zoning in Inwood, Manhattan
What is Inwood zoned?
Inwood is mostly R7A: 364 of its 541 tax lots (67.3%) are in R7A, based on PLUTO 26v2 lots inside the 2020 NTA boundary. R7A allows a standard residential FAR of 4.00 and a maximum height of 85 ft for standard buildings (ZR 23-22, ZR 23-432). Check any Inwood address free on Zohgo.
Inwood is mostly R7A apartment blocks, with a Special Inwood District on part of the neighborhood.
Inwood, at the top of Manhattan, is small by lot count: 541 tax lots in the 2020 Inwood NTA, with a median lot of 9,992 sq ft because most lots hold full apartment buildings. 364 lots (67.3%) are R7A, a contextual district with a standard FAR of 4.00 and an 85-foot height limit for standard residences (ZR 23-22, ZR 23-432).
175 lots (32.3%) also fall inside the Special Inwood District (ZR Article XIV, Chapter 2). The remaining lots are a mix of R7-2 (42), commercial districts such as C4-4D (20) and C4-4 (11), and a few manufacturing lots.
Zoning districts in Inwood by tax lot
| Zoning district (zonedist1) | Tax lots | Share | Standard residential FAR | Max height (standard residences) |
|---|---|---|---|---|
| R7A | 364 | 67.3% | 4.00 | base 40-75 ft, max 85 ft |
| R7-2 | 42 | 7.8% | 3.44 (4.00 within 100 ft of a wide street) | base 40-65 ft, max 75 ft (base 40-75 ft, max 85 ft within 100 ft of a wide street) |
| C4-4D (commercial) | 20 | 3.7% | 6.02 (as R8A, its residential equivalent) | |
| R8A | 16 | 3.0% | 6.02 | base 60-95 ft, max 125 ft |
| M1-5 (manufacturing) | 13 | 2.4% | manufacturing district | |
| C4-4 (commercial) | 11 | 2.0% | 3.44 (4.00 within 100 ft of a wide street) (as R7-2, its residential equivalent) | |
| R7D | 11 | 2.0% | 4.66 | base 60-85 ft, max 105 ft |
| C6-2 (commercial) | 9 | 1.7% | 6.02 (7.20 within 100 ft of a wide street) (as R8, its residential equivalent) | |
| C4-5D (commercial) | 8 | 1.5% | 4.66 (as R7D, its residential equivalent) | |
| M1-1 (manufacturing) | 7 | 1.3% | manufacturing district | |
| M1-4 (manufacturing) | 7 | 1.3% | manufacturing district | |
| M3-1 (manufacturing) | 6 | 1.1% | manufacturing district | |
| All other districts (10) | 27 | 5.0% | ||
| Total | 541 | 100% |
Source: PLUTO 26v2, field zonedist1 (the district covering the largest part of each lot), lots inside the 2020 NTA boundary MN1203. FAR and heights are the ZR 23-21 / 23-22 and ZR 23-421 / 23-422 / 23-432 limits for standard residences; qualifying affordable or senior housing can go higher. Commercial districts use their residential equivalent from ZR 34-112.
What the main districts allow
- R7A (67.3% of lots). Standard residential FAR 4.00; 5.01 for qualifying affordable or senior housing (ZR 23-22). Height: base 40-75 ft, max 85 ft; qualifying affordable or senior housing base up to 85 ft, max 115 ft (ZR 23-432).
- R7-2 (7.8% of lots). Standard residential FAR 3.44 (4.00 within 100 ft of a wide street); 5.01 for qualifying affordable or senior housing (ZR 23-22). Height: base 40-65 ft, max 75 ft (base 40-75 ft, max 85 ft within 100 ft of a wide street); qualifying affordable or senior housing max 105 ft (115 ft within 100 ft of a wide street) (ZR 23-432).
- R8A (3.0% of lots). Standard residential FAR 6.02; 7.20 for qualifying affordable or senior housing (ZR 23-22). Height: base 60-95 ft, max 125 ft; qualifying affordable or senior housing base up to 105 ft, max 145 ft (ZR 23-432).
Zohgo shows the zoning district, FAR, height and setbacks for any NYC address in about a minute. Free to start, sign in with Google or Apple.
Check any NYC address free on ZohgoCommercial overlays
152 lots (28.1%) carry a commercial overlay: C2-4 on 152 lots. An overlay sits on top of a residence district and allows local retail and services, usually on the ground floor of avenue and corridor buildings, while the residential rules of the underlying district still apply. For a zoning lot with only commercial use, the overlay FAR is 1.00 where the overlay is mapped in R1, R2, R3-1, R3A or R3X, 1.60 in R3-2, and 2.00 in R4 and every higher residence district (ZR 33-121).
Special districts
- Special Inwood District (IN): 175 lots. Rules in ZR Article XIV, Chapter 2 modify the underlying district.
Historic districts
15 lots (2.8%) sit in a designated historic district according to PLUTO, led by Park Terrace West-West 217th Street Historic District (15). Zoning still sets the envelope, but exterior work on these lots also goes through the Landmarks Preservation Commission, so a lot that zones for more floor area may not be able to use it.
18 lots (3.3%) are split by a district boundary (PLUTO splitzone). On those, each portion follows its own district; see split zoning lots.
Worked example
Take a 10,000 sq ft lot in R7A, close to the neighborhood's median lot size. At the standard FAR of 4.00, the maximum residential floor area is 10,000 x 4.00 = 40,000 sq ft (ZR 23-22). With qualifying affordable or senior housing rules the FAR is 5.01, so 10,000 x 5.01 = 50,100 sq ft. For a standard multiple dwelling outside special density areas, the unit cap divides floor area by the dwelling unit factor of 680: 40,000 / 680 = 58.82, which allows 59 units because fractions of 0.75 or more count as a unit (ZR 23-52).
How we counted
We took every tax lot in PLUTO 26v2 (NYC Department of City Planning, August 2026), kept lots whose latitude and longitude fall inside the 2020 Neighborhood Tabulation Area polygon for Inwood (MN1203), and counted the zoning district PLUTO lists first (zonedist1). Lot counts are not land area: one large lot counts the same as a 20-foot rowhouse lot. Zoning maps change through rezonings, so always confirm the district for a specific address.
Inwood zoning FAQ
What is the most common zoning district in Inwood?
R7A. In PLUTO 26v2, 364 of the 541 tax lots inside the 2020 Inwood NTA boundary (67.3%) have R7A as their main district.
What FAR does R7A allow?
R7A allows a standard residential FAR of 4.00 and 5.01 for qualifying affordable or senior housing (ZR 23-22).
How tall can a building be in R7A?
For standard residences: base 40-75 ft, max 85 ft. Qualifying affordable or senior housing: base up to 85 ft, max 115 ft (ZR 23-432).
How many apartments fit on a 10,000 sq ft R7A lot?
At FAR 4.00 the lot allows 40,000 sq ft of residential floor area. Divided by the dwelling unit factor of 680 that is 58.82, so 59 units for a standard building outside special density areas, since fractions of 0.75 or more count as a unit (ZR 23-52).
Related pages
Sources
Lot counts are our own tabulation of PLUTO 26v2 inside the 2020 NTA boundary, pulled October 27, 2026. PLUTO is updated a few times a year, so counts will drift.
- NYC Open Data: Primary Land Use Tax Lot Output (PLUTO), version 26v2, queried October 27, 2026: https://data.cityofnewyork.us/d/64uk-42ks
- NYC Open Data: 2020 Neighborhood Tabulation Areas (NTAs): https://data.cityofnewyork.us/d/9nt8-h7nd
- ZR 23-21: Floor area regulations for R1 through R5 Districts: https://zr.planning.nyc.gov/article-ii/chapter-3/23-21
- ZR 23-22: Floor area regulations for R6 through R12 Districts: https://zr.planning.nyc.gov/article-ii/chapter-3/23-22
- ZR 23-432: Height and setback requirements (R6-R12): https://zr.planning.nyc.gov/article-ii/chapter-3/23-432
- ZR 34-112: Residential equivalents in Commercial Districts: https://zr.planning.nyc.gov/article-iii/chapter-4/34-112
- ZR 33-121: Commercial FAR in overlay districts: https://zr.planning.nyc.gov/article-iii/chapter-3/33-121
- ZR Special Inwood District (IN): https://zr.planning.nyc.gov/article-xiv/chapter-2